Top Tips for Cleaning Art Pottery
It would be ideal if all pottery remained as clean and shiny as did when leaving the kiln. Unfortunately, antique and collectible art pottery has often seen some wear and tear from use over the years. Below are some tips on how to clean your art pottery to bring it back to like-new condition.
Dust
Dusty pottery can be cleaned with mild liquid soap and a quick rinse of warm water before drying with a soft towel. Pottery that is only lightly covered in dust could also be buffed with a paper towel, dampened with Windex cleaner.
Dirt and Grime
Dirty art pottery can be soaked for at least 24 hours in a hot water and ammonia mixture. Typically a cup of ammonia can be used per 2 gallons of water. Some people have reported additional success by adding Spic and Span to the ammonia/water mixture.
Sticker Residue and Glue
We have found De-Solv-it spray to be very effective in removing old sticker stains, glue and related marks on glazed art pottery. Typically you can just spray the De-Solv-it on a clean rag and rub on the problem area on the pottery and buff clean with a soft cloth.
Brittle, older unwanted labels may require a gentle scraping with a dull box knife to allow the De-Solv-it to better penetrate the label. We have also effectively used acetone on a cloth to remove stickers and glue from art pottery but acetone may damage any repairs on your pottery so be careful if you are unsure if your piece has been repaired.
Silver or Pencil Marks
Metal polish is very effective at removing silver or pencil marks from matte glazed art pottery such as Roseville, Rookwood, Van Briggle, Teco and others. We have experimented with a variety of brands over the years and have Noxon to consistently provide the best results for removing silver marks.
To use metal polish to remove silver and pencil marks from your art pottery, apply Noxon or other metal polish to a rag and aggressively rub the marked area. To remove or lighten the marks typically takes a significant amount of rubbing but the end result is definitely worth the effort. After the silver marks have been removed, the clean part of the rag can be used to remove any remaining polish and buff the glazed finish.
Paint Splatters
Specks of house paint can be removed in several ways. The adventurous cleaner may be able to gently fleck them off with a dull box knife or safety pin. On hard glazed pottery such as Roseville or Van Briggle, the paint specks may also be cleaned off with some buffing with stainless steel polish.
Acetone is also effective at removing these paint specs from glazed art pottery. For thicker and aged paint specs you sometimes need to use a safety pin or needle scuff or flake the paint to allow the acetone to work into the paint.
Hard Water and Mineral Deposit Buildup
If the interior or exterior of a pot is stained with mineral deposits such as calcium, lime, and rust stains, soaking in white vinegar can be an effective way to remove these deposits from pottery such as Rookwood, Weller, Van Briggle, Roseville and others.
For lighter deposit staining, soaking the vase a few days in the vinegar is sometimes all that is necessary to remove the mineral deposits. On pottery pieces that have more extensive mineral deposits, extended soaking may be required.
The extended soaking may take weeks to remove the deposits from your art pottery. On the more severe examples of lime and calcium buildup, you can scrape the deposits daily with a butter knife to help allow the vinegar to better penetrate the mineral deposits. When conducting extended soaking, it is also beneficial to routinely change the vinegar to maintain its strength.
After cleaning your art pottery with vinegar soaking, wash the vase with soap and warm water. You will then need to soak your art pottery in tap water until the vinegar smell is gone.
Darkened Crazing and Staining
Many art pottery restorers use hydrogen peroxide to lighten darkened crazing and stains on art pottery such as Roseville, Rookwood, Van Briggle, Weller, and other glazed art pottery. There are many different methods for using peroxide to effectively lighten darkened crazing.
A common method is to use undiluted 40% hydrogen peroxide. The crazing lightening process will not typically work if you use a lesser strength solution. 40% hydrogen peroxide will burn your skin so you must use waterproof gloves, goggles and protect all exposed skin.
The peroxide solution should be put in a sealed container that can hold the submerged vase. Peroxide will lose its strength over time if it is exposed to the air so it is important that the container used for soaking is airtight. The soaking process can take weeks and even months in some cases so you may need to periodically change the peroxide as it loses strength. Periodically check your art pottery to see if the crazing lightened to a satisfactory point; if not continue soaking. Often times this soaking procedure will be alternated with baking the vase at around 200degrees for 1 hour. Repeat this process periodically until the crazing and staining has lightened to your satisfaction.
PLEASE NOTE: Use any of these methods at your own risk as all pottery and associated dirt, grime and stains are different. What works in one case may not be at all effective in another and may in fact result in damage to your art pottery.